motorola
BEFOREYOU
BEGIN
®
Bluetooth
Handsfree Headset
Before using this product, read the Important Safety and
Legal Information pamphlet and follow its instructions.
Take a moment before you get started to
familiarize yourself with your new
H700 Headset.
Multi-Color
Indicator Light
Boom
Microphone
Volume
Buttons
Call
Button
Speaker
(on reverse
side)
H700
Get connected in 4 quick steps.
CHARGEYOUR
HEADSET
ENSUREYOUR
1
2
HEADSET IS IN
PAIRING MODE
Charge your headset's battery for 2 hours:
Before you can use your headset, you must pair
(link) it with your phone.
Open the headset boom to initiate easy
pairing. After a few moments, the indicator
light will be steadily lit in purple to indicate
headset is in pairing mode.
Plug the Motorola charger into the end of
the headset.
1
2
Indicator Light
(steadily purple
for pairing mode)
The indicator light turns red when the
battery is charging. It may take up to 1
minute for the indicator light to turn on.
When the headset's battery is fully charged
(about 2 hours), the indicator light turns
green.
If the headset does not enter pairing mode,
see TROUBLESHOOTING for help.
Disconnect the charger.
Note: Headset is not functional while charging.
TEST AND USE
USING YOUR H700
4
See
Features and
Your phone and headset are now paired and
ready to make and receive calls.To confirm they
are operating properly, make a call:
Functions Guide
on the reverse side
for information on
using your H700
Place the headset over your ear. See
"Wearing the Headset" on the reverse side
of this guide.
1
On your phone, dial the number you want
to call and press the Send key.
2
3
If your phone and headset are successfully
paired, you will hear ringing on the headset.
After you have successfully paired your phone
and headset, you don't need to repeat these
steps. For daily use, ensure that your headset is
turned ON and that your phone's Bluetooth
feature is ON.
To save battery power, turn OFF the headset
when you don't use it for an extended time by
closing the boom.
TURNING HEADSET
ON AND OFF
Features and
Functions Guide
To turn your headset on, open the headset
boom.The indicator light flashes blue.
To turn your headset off, close the
headset boom.The indicator light will turn
off.
H700
Bluetooth®
Handsfree Headset
IMPORTANT:
Be sure to first follow the
Quick Start Guide
on the reverse side
of this guide
Multi-Color
Indicator Light
to complete initial setup
of your H700.
WEARINGTHE
HEADSET
Open the headset boom, then open the
earhook.
CHANGING FOR USE
ON OTHER EAR
You can wear your H700 headset on your left or
right ear.The headset comes ready for the right
ear.To change the headset for the left ear:
1
Loop the earhook over your ear.
Press the headset to your ear.
2
3
Open the headset boom,
then open the earhook
1
(90 from the headset).
°
Point the headset boom towards your
mouth.
4
2
Gently lift and pull the
top of the earhook up
and off the upper hinge
pin.Then, pull it away to
remove it.
1 Open Earhook
2 Pull Earhook
Up
3
4
Flip the headset over.
Hook the bottom of the
earhook onto the lower
hinge pin, then lift and
pull the top of the
earhook over the upper
hinge pin.
Hinge
Pin
European Union Directives
Conformance Statement
CHANGINGVOLUME
BUTTON ORIENTATION
Hereby, Motorola declares that this
product is in compliance with:
You can also change the orientation of the
volume buttons on your headset.
• The essential requirements and
other relevant provisions of Directive
1999/5/EC.
Turn the headset power off.
1
2
• All other relevant EU Directives.
Press the Call button until the indicator
light becomes steadily lit in purple, then
press the Volume button you want to
assign as the "volume up" button.
Product
Approval
Number
The above gives an example of a typical Product
Approval Number.
Call
Button
You can view your product’s Declaration of Conformity
(DoC) to Directive 1999/5/EC (to R&TTE Directive) at
product Approval Number from your product’s label in
the “Search” bar on the web site.
Volume
Buttons
MAKING CALLS
MAKING CALLS CONTINUED
Function
Action
Function
Action
Make a voice dial call
Tap the Call button
and speak the
name after the tone
Answer a second
incoming call
Press and hold the
Call button (places
first call on hold)
End a call
Tap the Call button
Toggle between two
active calls
Press and hold
the Call button
Answer a call
Open headset boom
or tap the Call button
(if boom is already
open)
Join a 3-way call
Press and hold
both Volume buttons
Put an active call on
hold or resume a call
on hold
Press and hold the
Call button until you
hear a beep
Ignore a call
Press and hold the
Call button until you
hear a beep
Transfer a call from the
phone to the headset
Open headset boom
Redial last call
Press and hold the
Call button until you
hear a beep
Disable the
indicator light
Press and hold
both Volume
buttons for 3 to 4
seconds
Note:Your H700 supports both Handsfree and Headset
Profiles. Accessing call functions depends upon which
profile your phone supports. See your phone's user's guide
for more information.
Mute or unmute a call
Tap both Volume
buttons
Note: Some features are phone/network dependent.
AUDIOTONES
INDICATOR LIGHTS
The audio tones provide information about your
headset status.
With the Charger Plugged In
Indicator Light
Headset Status
Red (steady)
Charging (less than
80% charged)
AudioTone
Headset Status
Single high tone when
pressing Volume button
Volume at minimum
or maximum
Yellow (steady)
Green (steady)
Charging (more
than 80% charged)
Five rapid high tones
repeated every 60 sec.
Low battery
Charging complete
No audio indications;
deteriorating quality
Out of range
With No Charger Plugged In
Indicator Light
Off
Headset Status
Ring tone
Incoming call
Power off
Single high tone
Single low tone
Dual high/low tone
Pairing confirmation
Voice activation
Purple (steady)
Pairing mode/
Volume button
orientation
Voice tag not
recognized
Red
Battery low
Single high tone
Low to high tone
End call
Blue (10 rapid flashes)
Blue (slow pulse)
Blue (quick flash)
Pairing successful
Connected (on a call)
Standby (not on a call)
Phone network
not available
Two ascending tones
Two descending tones
Mute enabled
Mute disabled
Note: After 5 minutes of inactivity, the light stops flashing to
conserve power, but the headset remains in standby mode.
|